American Society for Testing and Materials (ASTM)

Documents

• ASTM-C805 – Concrete, Hardened, Rebound Number of (No S/S Document)
• ASTM-C811 – Concrete, for Application of Chemical-Resistant Resin Monolithic Surfacings, Surface Preparation of
• ASTM-C816 – Sulfur in Graphite by Combustion-Iodometric Titration Method
• ASTM-C822 – Concrete Pipe and Related Products
• ASTM-C823 – Examination and Sampling of Hardened Concrete in Constructions (No S/S Document)
• ASTM-C827 – MIXTURES, CYLINDRICAL SPECIMENS FROM CEMENTITIOUS, CHANGE IN HEIGHT AT EARLY AGES OF (NO S/S DOCUMENT)
• ASTM-C828 – Pipe Lines, Clay, Vitrified, Low-Pressure Air Test of
• ASTM-C834 – Latex Sealants
• ASTM-C836 – Membrane, Cold Liquid-Applied Elastomeric Waterproofing, for use with Separate Wearing Course, High Solids Content (S/S ASTM-C836/C836M)
• ASTM-C840 – Board, Gypsum, Application and Finishing of
• ASTM-C841 – Installation of Interior Lathing and Furring
• ASTM-C843 – Application of Gypsum Veneer Plaster
• ASTM-C844 – Application of Gypsum Base to Receive Gypsum Veneer Plaster
• ASTM-C847 – Metal Lath
• ASTM-C860 – Castable, Refractory, Using the Ball-in-Hand Test, Determining the Consistency of
• ASTM-C862 – Concrete Specimens by Casting, Preparing Refractory
• ASTM-C864 – Gaskets, Seal, Setting Blocks, and Spacers, Dense Elastomeric Compression (No S/S Document)
• ASTM-C865 – Concrete Specimens, Firing Refractory
• ASTM-C87 – Aggregate, Fine, Effect of Organic Impurities in, on Strength of Mortar, Standard Test Method for (See Notice of Withdrawal for Replacement Information)
• ASTM-C873 – Cylinders, Concrete, Cast in Place in Cylindrical Molds, Compressive Strength of (No S/S Document)
• ASTM-C88 – Sodium Sulfate or Magnesium Sulfate, Soundness of Aggregates by Use of
• ASTM-C881 – Concrete, Epoxy-Resin-Base Bonding Systems (No S/S Document)
• ASTM-C882 – Bond Strength of Epoxy-Resin Systems Used with Concrete by Slant Shear (No S/S Document)
• ASTM-C883 – CONCRETE, EFFECTIVE SHRINKAGE OF EPOXY-RESIN SYSTEMS USED WITH, STANDARD TEST METHOD FOR (NO S/S DOCUMENT)
• ASTM-C884-C884M – Concrete and an Epoxy-Resin Overlay, Thermal Compatibility Between
• ASTM-C889 – Chemical and Mass Spectrographic Analysis of Nuclear-Grade Gadolinium Oxide (GD203) Powder
• ASTM-C90 – Concrete Masonry Units, Loadbearing
• ASTM-C901 – Panels, Masonry, Prefabricated
• ASTM-C913 – Concrete Water, Precast, and Wastewater Structures
• ASTM-C916 – Insulation, Thermal, Duct, Adhesives for
• ASTM-C91-C91M – Standard Specification for Masonry Cement
• ASTM-C92 – Water Content and Sieve Analysis, of Refractory Materials
• ASTM-C920 – Sealants, Elastomeric Joint
• ASTM-C921 – Insulation, Thermal, Jacketing Materials for, Determining the Properties of
• ASTM-C923 – Pipes and Laterals, Resilient Connectors Between Reinforced Concrete Manhole Structures
• ASTM-C924 – Pipe Sewer Lines, Concrete, by Low-Pressure Air Test Method (No S/S Document)
• ASTM-C93 – FIREBRICK, INSULATING, COLD CRUSHING STRENGTH AND MODULUS OF RUPTURE OF (NO S/S DOCUMENT)
• ASTM-C930 – Standard Classification of Potential Health and Safety Concerns Associated With Thermal Insulation Materials and Accessories
• ASTM-C931-C931M – GYPSUM SOFFIT BOARD, EXTERIOR (NO S/S DOCUMENT)
• ASTM-C932 – Plastering, Exterior, Surface-Applied Bonding Compounds for
• ASTM-C937 – Grout Fluidifier for Preplaced-Aggregate Concrete
• ASTM-C939 – Grout for Preplaced-Aggregate Concrete (Flow Cone Method), Flow of
• ASTM-C942 – Grouts for Preplaced-Aggregate Concrete in the Laboratory, Compressive Strength of
• ASTM-C94-C94M – Concrete, Ready-Mixed
• ASTM-C952 – Standard Test Method for Bond Strength of Mortar to Masonry Units
• ASTM-C954 – Steel Drill Screws for the Application of Gypsum Panel Products of Metal Plaster Bases to Steel Studs From 0.033 In. (0.84 mm) to 0.112 In. (2.84 mm) in Thickness
• ASTM-C960-C960M – GYPSUM BOARD, PREDECORATED (NO S/S DOCUMENT)
• ASTM-C964 – Gasket, Lock-Strip, Glazing (No S/S Document)
• ASTM-C966 – Asbestos-Cement, Installing, Nonpressure Pipe
• ASTM-C969 – Pipe Sewer Lines, Concrete, Installed Precast, Infiltration and Exfiltration, Acceptance Testing of
• ASTM-C97 – Stone, Specific Gravity of Dimension, Absorption and Bulk (No S/S Document)
• ASTM-C977 – Soil Stabilization, Quicklime and Hydrated Lime
• ASTM-C984 – ROOF INSULATION, PERLITE BOARD AND RIGID CELLULAR POLYISOCYANURATE COMPOSITE (NO S/S DOCUMENT)
• ASTM-C989 – Cement, Slag for use in Concrete and Mortars
• ASTM-C99 – Stone, Modulus of Rupture of Dimension (No S/S Document)
• ASTM-C995 – Time of Flow of Fiber-Reinforced Concrete Through Inverted Slump Cone (No S/S Document)
• ASTM-D1000 – Tapes, Pressure-Sensitive Adhesive-Coated, Used for Electrical and Electronic Applications
• ASTM-D1002 – Metal Specimens, Single-Lap-Joint Adhesively Bonded, by Tension Loading (Metal-to-Metal), Apparent Shear Strength
• ASTM-D1003 – Plastics, Transparent, Haze and Luminous Transmittance of
• ASTM-D1004 – Tear Resistance (Graves Tear) of Plastic Film and Sheeting
• ASTM-D1005 – FILM, DRY, THICKNESS OF ORGANIC COATINGS USING MICROMETERS, MEASUREMENT OF
• ASTM-D1006 – PAINTS ON WOOD, CONDUCTING EXTERIOR EXPOSURE TESTS OF
• ASTM-D1008 – WATER VAPOR TRANSMISSION OF SHIPPING CONTAINERS (NO S/S DOCUMENT)
• ASTM-D1012 – ANILINE POINT & MIXED ANILINE POINT OF HYDROCARBON SOLVENTS (USE ASTM D611)
• ASTM-D1013 – Resins and Plastics, Determining Total Nitrogen (No S/S Document)
• ASTM-D1014 – Conducting Exterior Exposure Tests of Paints and Coatings on Metal Substrates
• ASTM-D1018 – Hydrogen in Petroleum Fractions
• ASTM-D1019 – PETROLEUM DISTILLATES, OLEFINIC PLUS AROMATIC HYDROCARBONS IN - 13 SEP 68 (NO S/S DOCUMENT)
• ASTM-D1030 – Paper and Paperboard, Fiber Analysis of (No S/S Document)
• ASTM-D1031 – WOOD BLOCK FLOORING FOR INTERIOR USE, CREOSOTED END-GRAIN (NO S/S DOCUMENT)
• ASTM-D1037 – Fiber, Wood-Base, and Particle Panel Materials, Evaluating Properties of
• ASTM-D1043 – Plastics as a Function of Temperature by Means of a Torsion Test, Stiffness Properties of
• ASTM-D1044 – Surface Abrasion, Resistance of Transparent Plastics to
• ASTM-D1047 – Poly(Vinyl Chloride) Jacket for Wire and Cable
• ASTM-D1048 – Rubber Insulation Blankets
• ASTM-D1049 – Rubber Insulating Covers
• ASTM-D1050 – Rubber Insulating Line Hose
• ASTM-D1052 – Rubber Deterioration-Cut Growth Using Ross Flexing Apparatus, Standard Specification for Measuring
• ASTM-D1053 – Rubber Property-Stiffening at Low Temperatures: Flexible Polymers and Coated Fabrics, Standard Test Methods for
• ASTM-D1054 – Rubber Property-Resilience using a Goodyear-Healey Rebound Pendulum (No S/S Document)
• ASTM-D1055 – Latex Foam, Flexible Cellular Materials (No S/S Document)
• ASTM-D1056 – Sponge or Expanded Rubber, Flexible Cellular Materials
• ASTM-D1059 – Yarn Number Based on Short-Length Specimens (No S/S Document)
• ASTM-D1062 – Bonds, Adhesive, Cleavage Strength of Metal-to-Metal
• ASTM-D1064 – Iron in Rosin Tall Oil Fatty Acids and Other Related Products (No S/S Document)
• ASTM-D1066 – Steam, Sampling - 03 ) OCT 69 (No S/S Document)
• ASTM-D1067 – Water, Acidity or Alkalinity of
• ASTM-D1068 – Iron in Water
• ASTM-D1073 – Aggregate, Fine, for Bituminous Paving Mixtures
• ASTM-D1075 – Water on Compressive Strength of Compacted Bituminous Mixtures, Effect of
• ASTM-D1076 – Rubber-Concentrated, Ammonia Preserved, Creamed, and Centrifuged Natural Latex
• ASTM-D1078 – Distillation Range of Volatile Organic Liquids
• ASTM-D1081 – EVALUATING PRESSURE SEALING PROPERTIES OF RUBBER & RUBBER- LIKE MATERIALS ( USE METHOD 3211 OF FED-STD-601)
• ASTM-D1084 – ADHESIVES, VISCOSITY OF
• ASTM-D1085 – PETROLEUM AND PETROLEUM PRODUCTS, GAGING (NO S/S DOCUMENT)
• ASTM-D1086 – PETROLEUM AND PETROLEUM PRODUCTS, MEASURING THE TEMPERATURE OF (NO S/S DOCUMENT)
• ASTM-D1091 – Phosphorus in Lubricating Oils and Additives
• ASTM-D1092 – Greases, Lubricating, Measuring Apparent Viscosity of
• ASTM-D1093 – Liquids, Hydrocarbon, and Their Distillation Residues, Acidity of
• ASTM-D1094 – Water Reaction of Aviation Fuels