FSC-MISC: Miscellaneous

Documents

• AND10001 – MOUNTING PAD AND DRIVE - TYPE 2 VACUUM AND HYDRAULIC POWER PUMPS
• AND10003 – MOUNTING PAD AND DRIVE - AIRCRAFT ENGINE FUEL PUMP (SEE DWG AND20003)
• AND10005 – MOUNTING PAD AND DRIVE - AIRCRAFT TACHOMETER (SEE DWG AND20005)
• AND10008 – MOUNTING PAD AND DRIVE - AIRCRAFT ENGINE POWER TAKE-OFF (FLANGE TYPE)
• AND10009 – MOUNTING PAD AND DRIVE - SMALL AIRCRAFT ENGINE STARTER
• AND10010 – MOUNTING PAD AND DRIVE - AIRCRAFT ENGINE PROPELLER GOVERNOR OR HYDRO-CONTROL VALVE
• AND10049 – BOSSES- FLUID CONNECTION, INTERNAL STRAIGHT THREAD (S/S BY MS 33649)
• AND10064 – Fittings - Installation of Flared Tube, Straight Threaded Connectors (Use MS21344)
• AND10065 – CONNECTION ASSEMBLY - FLEXIBLE, FLUID, STANDARD DESIGN OF (NO S/S DOCUMENT)
• AND10066 – CONNECTORS-ELECTRICAL, RECEPTACLES, INTEGRAL MOUNTING (USE MS33678)
• AND10074 – BOSS SPACING - HYDRAULIC (USE MS21343)
• AND10079 – TERMINAL - EYE AND FORK CABLE (NO S/S DOCUMENT)
• AND10080 – FITTING - INSTALLATION OF UNIVERSAL ELBOW (USE MS21345)
• AND10082 – FASTENER, INSTALLATION-SNAPSLIDE (S/S BY MS-21327)
• AND10087 – SCREW-INSTALLATION AND LIMITATIONS FOR USAGE OF SELF TAPPING (USE MS 33749)
• AND10102 – TUBING - STANDARD DIMENSIONS FOR ROUND SEAMLESS ALLOY STEEL (NO S/S DOCUMENT)
• AND10104 – Tubing, Steel, Corrosion-Resistant, Round, Standard Dimensions for
• AND10106 – TUBING - STANDARD SIZES FOR ALUMINUM ALLOY (52SO) ROUND
• AND10107 – TUBING - STANDARD SIZES FOR ALUMINUM ALLOY (24ST) ROUND
• AND10108 – TUBING - STANDARD SIZES FOR ALUMINUM ALLOY (61S) ROUND
• AND10119 – ALUMINUM ALLOY - STANDARD CONDITIONS AND SIZES FOR SHEET AND STRIP (24S)
• AND10125 – ALUMINUM WIRE - STANDARD ALLOYS, TEMPERS AND SIZES OF ROUND AND HEXAGON (FOR WELDING ROD AND GENERAL USE)
• AND10126 – ALUMINUM WIRE - STANDARD CONDITIONS AND SIZES FOR SHEET, STRIP
• AND10130 – ALUMINUM ROD AND BAR - STANDARD ALLOYS, TEMPERS AND SIZES OF ROUND AND HEXAGON
• AND10131 – ALUMINUM BAR - STANDARD ALLOYS, TEMPER AND SIZES OF SQUARE
• AND10132 – ALUMINUM BAR - STANDARD ALLOY AND TEMPER (24ST), AND SIZES OF RECTANGULAR
• AND10150 – STARTER DIAGRAM - HAND CRANK FLEXIBLE SHAFT
• AND10201 – SCREENS AND GASKETS - DESIGNS REQUIREMENTS FOR CARBURETOR
• AND10206 – PLUG - SHIELDED AIRCRAFT ENGINE SPARK (USE MIL-S-7886)
• AND10210 – FLANGE-SINGLE 12 CYLINDER 3 BOLT MAGNETO
• AND10211 – MOUNTING FLANGE - DOUBLE TYPE MAGNETO
• AND10214 – COUPLING ASSEMBLIES-DOUBLE TYPE MAGNETO DRIVE
• AND10215 – MOUNTING FLANGE-SINGLE TYPE MAGNETO (9 AND 14 CYL)
• AND10216 – THROTTLE-HANDLE DESIGN FOR ENGINE
• AND10217 – PLUG - 14 MM SHIELDED SPARK (USE MIL-S-7886)
• AND10219 – PLUG - 14 MM BRITISH TYPE SHIELDED SPARK (USE MIL-S-7886)
• AND10220 – VAPOR PRESSURE CHART (NO S/S DOCUMENT)
• AND10221 – VAPOR PRESSURE CORRECTION CHART
• AND10222 – FITTINGS-SYNTHETIC TANK GENERAL FEATURES OF CONSTRUCTION (SUPERSEDED IN PART )COVER( BY MS-33595 AND IN PART )FLANGE( BY MS-33596)
• AND10223 – LEVERS-CORRELATION OF POWER AND CONDITION
• AND10234 – TEMPLATE-PROPELLER BLADE MASTER MALE
• AND10235 – TEMPLATE-PROPELLER BLADE FEMALE
• AND10236 – TEMPLATE PROPELLER BLADE ANGLE CHECKING
• AND10237 – SPLINE, SERRATED (NO S/S DOCUMENT)
• AND10300 – INSTALLATION CLEARANCE&TYPE X DRIVE
• AND10306 – PROPELLER GOVERNOR INSTALLATION CLEARANCE AIRCRAFT ENGINE (FOR ENGINES OF 999 TAKE OFF H.P. OR LESS)
• AND10307 – PROPELLER GOVERNOR INSTALLATION CLEARANCE-AIRCRAFT ENGINE (FOR ENGINES OF 1000 TAKE OFF H.P. AND OVER)
• AND10312 – ELEMENT INSTALLATION CLEARANCE-ENGINE CYLINDER HEAD TEMPERATURE MEASURING
• AND10313 – RELIEF VALVE INSTALLATION CLEARANCE-HYDRAULIC
• AND10328 – INSTALLATION CLEARANCE-TYPE XL-B DRIVE MAGNETO
• AND10332 – STARTER-GENERATOR INSTALLATION CLEARANCE, TYPE XII DRIVE
• AND10334 – INSTALLATION CLEARANCE-TYPE XX DRIVE PROPELLER GOVERNOR
• AND10335 – INSTALLATION CLEARANCE-TYPE XIX DRIVE
• AND10342 – REGULATOR INSTALLATION CLEARANCE- DC GENERATOR VOLTAGE
• AND10355 – TOLERANCES-CARBON STEEL-SHEET AND STRIP (USE FED STD 48)
• AND10360 – TOLERANCE-CORROSION AND HEAT RESISTANT STEEL BARS, AND RODS AND WIRE (USE FED-STD-48)
• AND10362 – TOLERANCES-CARBON STEEL BAR AND ROD (USE FED STD 48)
• AND10367 – TOLERANCE-ALLOY STEEL SHEET AND STRIP (S/S BY FED-STD-48)
• AND10375 – COLOR-FLUID LINE IDENTIFICATION (USE MIL STD 1247)
• AND10379 – EQUIVALENTS-FRACTION AND DECIMAL
• AND10381 – SYMBOLS-MATERIAL
• AND10382 – GAUGE DIMENSIONS-STANDARD WIRE AND SHEET METAL
• AND10383 – CUTTING PLANE-EXAMPLE FOR
• AND10384 – CROSS SECTIONING-EXAMPLES FOR
• AND10385 – ALTERNATE POSITION-EXAMPLE
• AND10387 – Drill Sizes and Drilled Hole Tolerances Twist
• AND10388 – LINES-CONVENTIONAL
• AND10396 – NUMBER-AIRCRAFT ENGINE CYLINDER LOCATION DESIGNATION (USE MIL-STD-802)
• AND10398 – METALS, DEFINITION OF DISSIMILAR (S/S BY MS33586)
• AND10399 – NUMBER AIRCRAFT ENGINE LOCATION DESIGNATION (USE MIL-STD 802)
• AND10401 – CASE-STANDARDS DIMENSIONS FOR 2-3/4 DIAL INSTRUMENT
• AND10402 – CASE-STANDARDS DIMENSIONS FOR 2-3/4 DIAL INSTRUMENT (WITH SUMP)
• AND10403 – CASE-STANDARD DIMENSIONS FOR 1-7/8 DIAL INSTRUMENT (USE MS 33638)
• AND10404 – POINTERS-STANDARD DESIGN OF AIRCRAFT INSTRUMENT (USE MS33585)
• AND10406 – THERMOCOUPLE LEADS-IRON-CONSTANTAN, INSTALLATION OF
• AND10407 – INSULATOR - INSTALLATION OF VIBRATION
• AND10410 – PITOT-STATIC AND PITOT TUBE WIRING DIAGRAM FOR
• AND10411 – WIRING DIAGRAM-PERCENT TYPE TACHOMETER INDICATOR AND TWO POLE TACHOMETER GENERATOR
• AND10412 – CASE - 2-INCH SIZE INSTRUMENT, STANDARD DIMENSIONS FOR (USE MS33598)
• AND10413 – INSTRUMENT-FLIGHT, BASIC, STANDARD ARRANGEMENTS OF (S/S BY MS 33635)
• AND10425 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR, SHELL SIZES 8S, 10S, AND 10SL (USE MS33680)
• AND10426 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR, SHELL SIZES 12S AND 12 (USE MS33881)
• AND10428 – INSERT ARRANGEMENTS - ELECTRICAL CONNECTOR, SHELL SIZES 16S AND 16 (USE MS33683)
• AND10429 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR, SHELL SIZE 18 (USE MS33684)
• AND10431 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR, SHELL SIZE 22 (USE MS33686)
• AND10432 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR, SHELL SIZE 24 (USE MS 33687)
• AND10433 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR, SHELL SIZE 28 (USE MS33688)
• AND10434 – INSERT ARRANGEMENTS - ELECTRICAL CONNECTOR, SHELL SIZE 32 (USE MS33689)
• AND10435 – INSERT ARRANGEMENTS - ELECTRICAL CONNECTOR, SHELL SIZE 36 (USE MS33690)
• AND10436 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR SHELL SIZE 40 (S/S BY MS 33691)
• AND10437 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR SHELL SIZE 44 (S/S BY MS 33692)
• AND10438 – INSERT ARRANGEMENTS-ELECTRICAL CONNECTOR SHELL SIZE 48 (S/S BY MS 33693)
• AND10439 – RECEPTACLE INSTALLATION-FUEL NOZZLE GROUNDING (USE MS 33645)
• AND10440 – INSERT DESIGN-ELECTRICAL CONNECTOR, SHELL SIZE 18, ARRANGEMENT 16 (USE MS33694)
• AND10441 – BATTERY INSTALLATION
• AND10443 – CONTACTS-VIDEO COAXIAL CONNECTOR (USE MS33695)
• AND10444 – INSERT ARRANGEMENTS - ELECTRICAL AND COAXIAL CONNECTOR, SHELL SIZE 32 (USE MS33696)
• AND10445 – SUMP JAR-INSTALLATION OF BATTERY
• AND10446 – COMPASS WIRING DIAGRAM-REMOTE INDICATING MAGNETIC
• AND10447 – TACHOMETER AND SYNCHROSCOPE WIRING DIAGRAM-SINGLE AND MULTI-ENGINE